1/* SPDX-License-Identifier: GPL-2.0 */
2#ifndef __LINUX_UHCI_HCD_H
3#define __LINUX_UHCI_HCD_H
4
5#include <linux/list.h>
6#include <linux/usb.h>
7#include <linux/clk.h>
8
9#define usb_packetid(pipe) (usb_pipein(pipe) ? USB_PID_IN : USB_PID_OUT)
10#define PIPE_DEVEP_MASK 0x0007ff00
11
12
13/*
14 * Universal Host Controller Interface data structures and defines
15 */
16
17/* Command register */
18#define USBCMD 0
19#define USBCMD_RS 0x0001 /* Run/Stop */
20#define USBCMD_HCRESET 0x0002 /* Host reset */
21#define USBCMD_GRESET 0x0004 /* Global reset */
22#define USBCMD_EGSM 0x0008 /* Global Suspend Mode */
23#define USBCMD_FGR 0x0010 /* Force Global Resume */
24#define USBCMD_SWDBG 0x0020 /* SW Debug mode */
25#define USBCMD_CF 0x0040 /* Config Flag (sw only) */
26#define USBCMD_MAXP 0x0080 /* Max Packet (0 = 32, 1 = 64) */
27
28/* Status register */
29#define USBSTS 2
30#define USBSTS_USBINT 0x0001 /* Interrupt due to IOC */
31#define USBSTS_ERROR 0x0002 /* Interrupt due to error */
32#define USBSTS_RD 0x0004 /* Resume Detect */
33#define USBSTS_HSE 0x0008 /* Host System Error: PCI problems */
34#define USBSTS_HCPE 0x0010 /* Host Controller Process Error:
35 * the schedule is buggy */
36#define USBSTS_HCH 0x0020 /* HC Halted */
37
38/* Interrupt enable register */
39#define USBINTR 4
40#define USBINTR_TIMEOUT 0x0001 /* Timeout/CRC error enable */
41#define USBINTR_RESUME 0x0002 /* Resume interrupt enable */
42#define USBINTR_IOC 0x0004 /* Interrupt On Complete enable */
43#define USBINTR_SP 0x0008 /* Short packet interrupt enable */
44
45#define USBFRNUM 6
46#define USBFLBASEADD 8
47#define USBSOF 12
48#define USBSOF_DEFAULT 64 /* Frame length is exactly 1 ms */
49
50/* USB port status and control registers */
51#define USBPORTSC1 16
52#define USBPORTSC2 18
53#define USBPORTSC3 20
54#define USBPORTSC4 22
55#define USBPORTSC_CCS 0x0001 /* Current Connect Status
56 * ("device present") */
57#define USBPORTSC_CSC 0x0002 /* Connect Status Change */
58#define USBPORTSC_PE 0x0004 /* Port Enable */
59#define USBPORTSC_PEC 0x0008 /* Port Enable Change */
60#define USBPORTSC_DPLUS 0x0010 /* D+ high (line status) */
61#define USBPORTSC_DMINUS 0x0020 /* D- high (line status) */
62#define USBPORTSC_RD 0x0040 /* Resume Detect */
63#define USBPORTSC_RES1 0x0080 /* reserved, always 1 */
64#define USBPORTSC_LSDA 0x0100 /* Low Speed Device Attached */
65#define USBPORTSC_PR 0x0200 /* Port Reset */
66/* OC and OCC from Intel 430TX and later (not UHCI 1.1d spec) */
67#define USBPORTSC_OC 0x0400 /* Over Current condition */
68#define USBPORTSC_OCC 0x0800 /* Over Current Change R/WC */
69#define USBPORTSC_SUSP 0x1000 /* Suspend */
70#define USBPORTSC_RES2 0x2000 /* reserved, write zeroes */
71#define USBPORTSC_RES3 0x4000 /* reserved, write zeroes */
72#define USBPORTSC_RES4 0x8000 /* reserved, write zeroes */
73
74/* PCI legacy support register */
75#define USBLEGSUP 0xc0
76#define USBLEGSUP_DEFAULT 0x2000 /* only PIRQ enable set */
77#define USBLEGSUP_RWC 0x8f00 /* the R/WC bits */
78#define USBLEGSUP_RO 0x5040 /* R/O and reserved bits */
79
80/* PCI Intel-specific resume-enable register */
81#define USBRES_INTEL 0xc4
82#define USBPORT1EN 0x01
83#define USBPORT2EN 0x02
84
85#define UHCI_PTR_BITS(uhci) cpu_to_hc32((uhci), 0x000F)
86#define UHCI_PTR_TERM(uhci) cpu_to_hc32((uhci), 0x0001)
87#define UHCI_PTR_QH(uhci) cpu_to_hc32((uhci), 0x0002)
88#define UHCI_PTR_DEPTH(uhci) cpu_to_hc32((uhci), 0x0004)
89#define UHCI_PTR_BREADTH(uhci) cpu_to_hc32((uhci), 0x0000)
90
91#define UHCI_NUMFRAMES 1024 /* in the frame list [array] */
92#define UHCI_MAX_SOF_NUMBER 2047 /* in an SOF packet */
93#define CAN_SCHEDULE_FRAMES 1000 /* how far in the future frames
94 * can be scheduled */
95#define MAX_PHASE 32 /* Periodic scheduling length */
96
97/* When no queues need Full-Speed Bandwidth Reclamation,
98 * delay this long before turning FSBR off */
99#define FSBR_OFF_DELAY msecs_to_jiffies(10)
100
101/* If a queue hasn't advanced after this much time, assume it is stuck */
102#define QH_WAIT_TIMEOUT msecs_to_jiffies(200)
103
104
105/*
106 * __hc32 and __hc16 are "Host Controller" types, they may be equivalent to
107 * __leXX (normally) or __beXX (given UHCI_BIG_ENDIAN_DESC), depending on
108 * the host controller implementation.
109 *
110 * To facilitate the strongest possible byte-order checking from "sparse"
111 * and so on, we use __leXX unless that's not practical.
112 */
113#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_DESC
114typedef __u32 __bitwise __hc32;
115typedef __u16 __bitwise __hc16;
116#else
117#define __hc32 __le32
118#define __hc16 __le16
119#endif
120
121/*
122 * Queue Headers
123 */
124
125/*
126 * One role of a QH is to hold a queue of TDs for some endpoint. One QH goes
127 * with each endpoint, and qh->element (updated by the HC) is either:
128 * - the next unprocessed TD in the endpoint's queue, or
129 * - UHCI_PTR_TERM (when there's no more traffic for this endpoint).
130 *
131 * The other role of a QH is to serve as a "skeleton" framelist entry, so we
132 * can easily splice a QH for some endpoint into the schedule at the right
133 * place. Then qh->element is UHCI_PTR_TERM.
134 *
135 * In the schedule, qh->link maintains a list of QHs seen by the HC:
136 * skel1 --> ep1-qh --> ep2-qh --> ... --> skel2 --> ...
137 *
138 * qh->node is the software equivalent of qh->link. The differences
139 * are that the software list is doubly-linked and QHs in the UNLINKING
140 * state are on the software list but not the hardware schedule.
141 *
142 * For bookkeeping purposes we maintain QHs even for Isochronous endpoints,
143 * but they never get added to the hardware schedule.
144 */
145#define QH_STATE_IDLE 1 /* QH is not being used */
146#define QH_STATE_UNLINKING 2 /* QH has been removed from the
147 * schedule but the hardware may
148 * still be using it */
149#define QH_STATE_ACTIVE 3 /* QH is on the schedule */
150
151struct uhci_qh {
152 /* Hardware fields */
153 __hc32 link; /* Next QH in the schedule */
154 __hc32 element; /* Queue element (TD) pointer */
155
156 /* Software fields */
157 dma_addr_t dma_handle;
158
159 struct list_head node; /* Node in the list of QHs */
160 struct usb_host_endpoint *hep; /* Endpoint information */
161 struct usb_device *udev;
162 struct list_head queue; /* Queue of urbps for this QH */
163 struct uhci_td *dummy_td; /* Dummy TD to end the queue */
164 struct uhci_td *post_td; /* Last TD completed */
165
166 struct usb_iso_packet_descriptor *iso_packet_desc;
167 /* Next urb->iso_frame_desc entry */
168 unsigned long advance_jiffies; /* Time of last queue advance */
169 unsigned int unlink_frame; /* When the QH was unlinked */
170 unsigned int period; /* For Interrupt and Isochronous QHs */
171 short phase; /* Between 0 and period-1 */
172 short load; /* Periodic time requirement, in us */
173 unsigned int iso_frame; /* Frame # for iso_packet_desc */
174
175 int state; /* QH_STATE_xxx; see above */
176 int type; /* Queue type (control, bulk, etc) */
177 int skel; /* Skeleton queue number */
178
179 unsigned int initial_toggle:1; /* Endpoint's current toggle value */
180 unsigned int needs_fixup:1; /* Must fix the TD toggle values */
181 unsigned int is_stopped:1; /* Queue was stopped by error/unlink */
182 unsigned int wait_expired:1; /* QH_WAIT_TIMEOUT has expired */
183 unsigned int bandwidth_reserved:1; /* Periodic bandwidth has
184 * been allocated */
185} __attribute__((aligned(16)));
186
187/*
188 * We need a special accessor for the element pointer because it is
189 * subject to asynchronous updates by the controller.
190 */
191#define qh_element(qh) READ_ONCE((qh)->element)
192
193#define LINK_TO_QH(uhci, qh) (UHCI_PTR_QH((uhci)) | \
194 cpu_to_hc32((uhci), (qh)->dma_handle))
195
196
197/*
198 * Transfer Descriptors
199 */
200
201/*
202 * for TD <status>:
203 */
204#define TD_CTRL_SPD (1 << 29) /* Short Packet Detect */
205#define TD_CTRL_C_ERR_MASK (3 << 27) /* Error Counter bits */
206#define TD_CTRL_C_ERR_SHIFT 27
207#define TD_CTRL_LS (1 << 26) /* Low Speed Device */
208#define TD_CTRL_IOS (1 << 25) /* Isochronous Select */
209#define TD_CTRL_IOC (1 << 24) /* Interrupt on Complete */
210#define TD_CTRL_ACTIVE (1 << 23) /* TD Active */
211#define TD_CTRL_STALLED (1 << 22) /* TD Stalled */
212#define TD_CTRL_DBUFERR (1 << 21) /* Data Buffer Error */
213#define TD_CTRL_BABBLE (1 << 20) /* Babble Detected */
214#define TD_CTRL_NAK (1 << 19) /* NAK Received */
215#define TD_CTRL_CRCTIMEO (1 << 18) /* CRC/Time Out Error */
216#define TD_CTRL_BITSTUFF (1 << 17) /* Bit Stuff Error */
217#define TD_CTRL_ACTLEN_MASK 0x7FF /* actual length, encoded as n - 1 */
218
219#define uhci_maxerr(err) ((err) << TD_CTRL_C_ERR_SHIFT)
220#define uhci_status_bits(ctrl_sts) ((ctrl_sts) & 0xF60000)
221#define uhci_actual_length(ctrl_sts) (((ctrl_sts) + 1) & \
222 TD_CTRL_ACTLEN_MASK) /* 1-based */
223
224/*
225 * for TD <info>: (a.k.a. Token)
226 */
227#define td_token(uhci, td) hc32_to_cpu((uhci), (td)->token)
228#define TD_TOKEN_DEVADDR_SHIFT 8
229#define TD_TOKEN_TOGGLE_SHIFT 19
230#define TD_TOKEN_TOGGLE (1 << 19)
231#define TD_TOKEN_EXPLEN_SHIFT 21
232#define TD_TOKEN_EXPLEN_MASK 0x7FF /* expected length, encoded as n-1 */
233#define TD_TOKEN_PID_MASK 0xFF
234
235#define uhci_explen(len) ((((len) - 1) & TD_TOKEN_EXPLEN_MASK) << \
236 TD_TOKEN_EXPLEN_SHIFT)
237
238#define uhci_expected_length(token) ((((token) >> TD_TOKEN_EXPLEN_SHIFT) + \
239 1) & TD_TOKEN_EXPLEN_MASK)
240#define uhci_toggle(token) (((token) >> TD_TOKEN_TOGGLE_SHIFT) & 1)
241#define uhci_endpoint(token) (((token) >> 15) & 0xf)
242#define uhci_devaddr(token) (((token) >> TD_TOKEN_DEVADDR_SHIFT) & 0x7f)
243#define uhci_devep(token) (((token) >> TD_TOKEN_DEVADDR_SHIFT) & 0x7ff)
244#define uhci_packetid(token) ((token) & TD_TOKEN_PID_MASK)
245#define uhci_packetout(token) (uhci_packetid(token) != USB_PID_IN)
246#define uhci_packetin(token) (uhci_packetid(token) == USB_PID_IN)
247
248/*
249 * The documentation says "4 words for hardware, 4 words for software".
250 *
251 * That's silly, the hardware doesn't care. The hardware only cares that
252 * the hardware words are 16-byte aligned, and we can have any amount of
253 * sw space after the TD entry.
254 *
255 * td->link points to either another TD (not necessarily for the same urb or
256 * even the same endpoint), or nothing (PTR_TERM), or a QH.
257 */
258struct uhci_td {
259 /* Hardware fields */
260 __hc32 link;
261 __hc32 status;
262 __hc32 token;
263 __hc32 buffer;
264
265 /* Software fields */
266 dma_addr_t dma_handle;
267
268 struct list_head list;
269
270 int frame; /* for iso: what frame? */
271 struct list_head fl_list;
272} __attribute__((aligned(16)));
273
274/*
275 * We need a special accessor for the control/status word because it is
276 * subject to asynchronous updates by the controller.
277 */
278#define td_status(uhci, td) hc32_to_cpu((uhci), \
279 READ_ONCE((td)->status))
280
281#define LINK_TO_TD(uhci, td) (cpu_to_hc32((uhci), (td)->dma_handle))
282
283
284/*
285 * Skeleton Queue Headers
286 */
287
288/*
289 * The UHCI driver uses QHs with Interrupt, Control and Bulk URBs for
290 * automatic queuing. To make it easy to insert entries into the schedule,
291 * we have a skeleton of QHs for each predefined Interrupt latency.
292 * Asynchronous QHs (low-speed control, full-speed control, and bulk)
293 * go onto the period-1 interrupt list, since they all get accessed on
294 * every frame.
295 *
296 * When we want to add a new QH, we add it to the list starting from the
297 * appropriate skeleton QH. For instance, the schedule can look like this:
298 *
299 * skel int128 QH
300 * dev 1 interrupt QH
301 * dev 5 interrupt QH
302 * skel int64 QH
303 * skel int32 QH
304 * ...
305 * skel int1 + async QH
306 * dev 5 low-speed control QH
307 * dev 1 bulk QH
308 * dev 2 bulk QH
309 *
310 * There is a special terminating QH used to keep full-speed bandwidth
311 * reclamation active when no full-speed control or bulk QHs are linked
312 * into the schedule. It has an inactive TD (to work around a PIIX bug,
313 * see the Intel errata) and it points back to itself.
314 *
315 * There's a special skeleton QH for Isochronous QHs which never appears
316 * on the schedule. Isochronous TDs go on the schedule before the
317 * skeleton QHs. The hardware accesses them directly rather than
318 * through their QH, which is used only for bookkeeping purposes.
319 * While the UHCI spec doesn't forbid the use of QHs for Isochronous,
320 * it doesn't use them either. And the spec says that queues never
321 * advance on an error completion status, which makes them totally
322 * unsuitable for Isochronous transfers.
323 *
324 * There's also a special skeleton QH used for QHs which are in the process
325 * of unlinking and so may still be in use by the hardware. It too never
326 * appears on the schedule.
327 */
328
329#define UHCI_NUM_SKELQH 11
330#define SKEL_UNLINK 0
331#define skel_unlink_qh skelqh[SKEL_UNLINK]
332#define SKEL_ISO 1
333#define skel_iso_qh skelqh[SKEL_ISO]
334 /* int128, int64, ..., int1 = 2, 3, ..., 9 */
335#define SKEL_INDEX(exponent) (9 - exponent)
336#define SKEL_ASYNC 9
337#define skel_async_qh skelqh[SKEL_ASYNC]
338#define SKEL_TERM 10
339#define skel_term_qh skelqh[SKEL_TERM]
340
341/* The following entries refer to sublists of skel_async_qh */
342#define SKEL_LS_CONTROL 20
343#define SKEL_FS_CONTROL 21
344#define SKEL_FSBR SKEL_FS_CONTROL
345#define SKEL_BULK 22
346
347/*
348 * The UHCI controller and root hub
349 */
350
351/*
352 * States for the root hub:
353 *
354 * To prevent "bouncing" in the presence of electrical noise,
355 * when there are no devices attached we delay for 1 second in the
356 * RUNNING_NODEVS state before switching to the AUTO_STOPPED state.
357 *
358 * (Note that the AUTO_STOPPED state won't be necessary once the hub
359 * driver learns to autosuspend.)
360 */
361enum uhci_rh_state {
362 /* In the following states the HC must be halted.
363 * These two must come first. */
364 UHCI_RH_RESET,
365 UHCI_RH_SUSPENDED,
366
367 UHCI_RH_AUTO_STOPPED,
368 UHCI_RH_RESUMING,
369
370 /* In this state the HC changes from running to halted,
371 * so it can legally appear either way. */
372 UHCI_RH_SUSPENDING,
373
374 /* In the following states it's an error if the HC is halted.
375 * These two must come last. */
376 UHCI_RH_RUNNING, /* The normal state */
377 UHCI_RH_RUNNING_NODEVS, /* Running with no devices attached */
378};
379
380/*
381 * The full UHCI controller information:
382 */
383struct uhci_hcd {
384 /* Grabbed from PCI */
385 unsigned long io_addr;
386
387 /* Used when registers are memory mapped */
388 void __iomem *regs;
389
390 struct dma_pool *qh_pool;
391 struct dma_pool *td_pool;
392
393 struct uhci_td *term_td; /* Terminating TD, see UHCI bug */
394 struct uhci_qh *skelqh[UHCI_NUM_SKELQH]; /* Skeleton QHs */
395 struct uhci_qh *next_qh; /* Next QH to scan */
396
397 spinlock_t lock;
398
399 dma_addr_t frame_dma_handle; /* Hardware frame list */
400 __hc32 *frame;
401 void **frame_cpu; /* CPU's frame list */
402
403 enum uhci_rh_state rh_state;
404 unsigned long auto_stop_time; /* When to AUTO_STOP */
405
406 unsigned int frame_number; /* As of last check */
407 unsigned int is_stopped;
408#define UHCI_IS_STOPPED 9999 /* Larger than a frame # */
409 unsigned int last_iso_frame; /* Frame of last scan */
410 unsigned int cur_iso_frame; /* Frame for current scan */
411
412 unsigned int scan_in_progress:1; /* Schedule scan is running */
413 unsigned int need_rescan:1; /* Redo the schedule scan */
414 unsigned int dead:1; /* Controller has died */
415 unsigned int RD_enable:1; /* Suspended root hub with
416 Resume-Detect interrupts
417 enabled */
418 unsigned int is_initialized:1; /* Data structure is usable */
419 unsigned int fsbr_is_on:1; /* FSBR is turned on */
420 unsigned int fsbr_is_wanted:1; /* Does any URB want FSBR? */
421 unsigned int fsbr_expiring:1; /* FSBR is timing out */
422
423 struct timer_list fsbr_timer; /* For turning off FBSR */
424
425 /* Silicon quirks */
426 unsigned int oc_low:1; /* OverCurrent bit active low */
427 unsigned int wait_for_hp:1; /* Wait for HP port reset */
428 unsigned int big_endian_mmio:1; /* Big endian registers */
429 unsigned int big_endian_desc:1; /* Big endian descriptors */
430 unsigned int is_aspeed:1; /* Aspeed impl. workarounds */
431
432 /* Support for port suspend/resume/reset */
433 unsigned long port_c_suspend; /* Bit-arrays of ports */
434 unsigned long resuming_ports;
435 unsigned long ports_timeout; /* Time to stop signalling */
436
437 struct list_head idle_qh_list; /* Where the idle QHs live */
438
439 int rh_numports; /* Number of root-hub ports */
440
441 wait_queue_head_t waitqh; /* endpoint_disable waiters */
442 int num_waiting; /* Number of waiters */
443
444 int total_load; /* Sum of array values */
445 short load[MAX_PHASE]; /* Periodic allocations */
446
447 struct clk *clk; /* (optional) clock source */
448
449 /* Reset host controller */
450 void (*reset_hc) (struct uhci_hcd *uhci);
451 int (*check_and_reset_hc) (struct uhci_hcd *uhci);
452 /* configure_hc should perform arch specific settings, if needed */
453 void (*configure_hc) (struct uhci_hcd *uhci);
454 /* Check for broken resume detect interrupts */
455 int (*resume_detect_interrupts_are_broken) (struct uhci_hcd *uhci);
456 /* Check for broken global suspend */
457 int (*global_suspend_mode_is_broken) (struct uhci_hcd *uhci);
458};
459
460/* Convert between a usb_hcd pointer and the corresponding uhci_hcd */
461static inline struct uhci_hcd *hcd_to_uhci(struct usb_hcd *hcd)
462{
463 return (struct uhci_hcd *) (hcd->hcd_priv);
464}
465static inline struct usb_hcd *uhci_to_hcd(struct uhci_hcd *uhci)
466{
467 return container_of((void *) uhci, struct usb_hcd, hcd_priv);
468}
469
470#define uhci_dev(u) (uhci_to_hcd(u)->self.controller)
471
472/* Utility macro for comparing frame numbers */
473#define uhci_frame_before_eq(f1, f2) (0 <= (int) ((f2) - (f1)))
474
475
476/*
477 * Private per-URB data
478 */
479struct urb_priv {
480 struct list_head node; /* Node in the QH's urbp list */
481
482 struct urb *urb;
483
484 struct uhci_qh *qh; /* QH for this URB */
485 struct list_head td_list;
486
487 unsigned fsbr:1; /* URB wants FSBR */
488};
489
490
491/* Some special IDs */
492
493#define PCI_VENDOR_ID_GENESYS 0x17a0
494#define PCI_DEVICE_ID_GL880S_UHCI 0x8083
495
496/* Aspeed SoC needs some quirks */
497static inline bool uhci_is_aspeed(const struct uhci_hcd *uhci)
498{
499 return IS_ENABLED(CONFIG_USB_UHCI_ASPEED) && uhci->is_aspeed;
500}
501
502/*
503 * Functions used to access controller registers. The UCHI spec says that host
504 * controller I/O registers are mapped into PCI I/O space. For non-PCI hosts
505 * we use memory mapped registers.
506 */
507
508#ifdef CONFIG_HAS_IOPORT
509#define UHCI_IN(x) x
510#define UHCI_OUT(x) x
511#else
512#define UHCI_IN(x) 0
513#define UHCI_OUT(x) do { } while (0)
514#endif
515
516#ifndef CONFIG_USB_UHCI_SUPPORT_NON_PCI_HC
517/* Support PCI only */
518static inline u32 uhci_readl(const struct uhci_hcd *uhci, int reg)
519{
520 return inl(port: uhci->io_addr + reg);
521}
522
523static inline void uhci_writel(const struct uhci_hcd *uhci, u32 val, int reg)
524{
525 outl(value: val, port: uhci->io_addr + reg);
526}
527
528static inline u16 uhci_readw(const struct uhci_hcd *uhci, int reg)
529{
530 return inw(port: uhci->io_addr + reg);
531}
532
533static inline void uhci_writew(const struct uhci_hcd *uhci, u16 val, int reg)
534{
535 outw(value: val, port: uhci->io_addr + reg);
536}
537
538static inline u8 uhci_readb(const struct uhci_hcd *uhci, int reg)
539{
540 return inb(port: uhci->io_addr + reg);
541}
542
543static inline void uhci_writeb(const struct uhci_hcd *uhci, u8 val, int reg)
544{
545 outb(value: val, port: uhci->io_addr + reg);
546}
547
548#else
549/* Support non-PCI host controllers */
550#if defined(CONFIG_USB_PCI) && defined(HAS_IOPORT)
551/* Support PCI and non-PCI host controllers */
552#define uhci_has_pci_registers(u) ((u)->io_addr != 0)
553#else
554/* Support non-PCI host controllers only */
555#define uhci_has_pci_registers(u) 0
556#endif
557
558#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
559/* Support (non-PCI) big endian host controllers */
560#define uhci_big_endian_mmio(u) ((u)->big_endian_mmio)
561#else
562#define uhci_big_endian_mmio(u) 0
563#endif
564
565static inline int uhci_aspeed_reg(unsigned int reg)
566{
567 switch (reg) {
568 case USBCMD:
569 return 00;
570 case USBSTS:
571 return 0x04;
572 case USBINTR:
573 return 0x08;
574 case USBFRNUM:
575 return 0x80;
576 case USBFLBASEADD:
577 return 0x0c;
578 case USBSOF:
579 return 0x84;
580 case USBPORTSC1:
581 return 0x88;
582 case USBPORTSC2:
583 return 0x8c;
584 case USBPORTSC3:
585 return 0x90;
586 case USBPORTSC4:
587 return 0x94;
588 default:
589 pr_warn("UHCI: Unsupported register 0x%02x on Aspeed\n", reg);
590 /* Return an unimplemented register */
591 return 0x10;
592 }
593}
594
595static inline u32 uhci_readl(const struct uhci_hcd *uhci, int reg)
596{
597 if (uhci_has_pci_registers(uhci))
598 return UHCI_IN(inl(uhci->io_addr + reg));
599 else if (uhci_is_aspeed(uhci))
600 return readl(uhci->regs + uhci_aspeed_reg(reg));
601#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
602 else if (uhci_big_endian_mmio(uhci))
603 return readl_be(uhci->regs + reg);
604#endif
605 else
606 return readl(uhci->regs + reg);
607}
608
609static inline void uhci_writel(const struct uhci_hcd *uhci, u32 val, int reg)
610{
611 if (uhci_has_pci_registers(uhci))
612 UHCI_OUT(outl(val, uhci->io_addr + reg));
613 else if (uhci_is_aspeed(uhci))
614 writel(val, uhci->regs + uhci_aspeed_reg(reg));
615#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
616 else if (uhci_big_endian_mmio(uhci))
617 writel_be(val, uhci->regs + reg);
618#endif
619 else
620 writel(val, uhci->regs + reg);
621}
622
623static inline u16 uhci_readw(const struct uhci_hcd *uhci, int reg)
624{
625 if (uhci_has_pci_registers(uhci))
626 return UHCI_IN(inw(uhci->io_addr + reg));
627 else if (uhci_is_aspeed(uhci))
628 return readl(uhci->regs + uhci_aspeed_reg(reg));
629#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
630 else if (uhci_big_endian_mmio(uhci))
631 return readw_be(uhci->regs + reg);
632#endif
633 else
634 return readw(uhci->regs + reg);
635}
636
637static inline void uhci_writew(const struct uhci_hcd *uhci, u16 val, int reg)
638{
639 if (uhci_has_pci_registers(uhci))
640 UHCI_OUT(outw(val, uhci->io_addr + reg));
641 else if (uhci_is_aspeed(uhci))
642 writel(val, uhci->regs + uhci_aspeed_reg(reg));
643#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
644 else if (uhci_big_endian_mmio(uhci))
645 writew_be(val, uhci->regs + reg);
646#endif
647 else
648 writew(val, uhci->regs + reg);
649}
650
651static inline u8 uhci_readb(const struct uhci_hcd *uhci, int reg)
652{
653 if (uhci_has_pci_registers(uhci))
654 return UHCI_IN(inb(uhci->io_addr + reg));
655 else if (uhci_is_aspeed(uhci))
656 return readl(uhci->regs + uhci_aspeed_reg(reg));
657#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
658 else if (uhci_big_endian_mmio(uhci))
659 return readb_be(uhci->regs + reg);
660#endif
661 else
662 return readb(uhci->regs + reg);
663}
664
665static inline void uhci_writeb(const struct uhci_hcd *uhci, u8 val, int reg)
666{
667 if (uhci_has_pci_registers(uhci))
668 UHCI_OUT(outb(val, uhci->io_addr + reg));
669 else if (uhci_is_aspeed(uhci))
670 writel(val, uhci->regs + uhci_aspeed_reg(reg));
671#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_MMIO
672 else if (uhci_big_endian_mmio(uhci))
673 writeb_be(val, uhci->regs + reg);
674#endif
675 else
676 writeb(val, uhci->regs + reg);
677}
678#endif /* CONFIG_USB_UHCI_SUPPORT_NON_PCI_HC */
679#undef UHCI_IN
680#undef UHCI_OUT
681
682/*
683 * The GRLIB GRUSBHC controller can use big endian format for its descriptors.
684 *
685 * UHCI controllers accessed through PCI work normally (little-endian
686 * everywhere), so we don't bother supporting a BE-only mode.
687 */
688#ifdef CONFIG_USB_UHCI_BIG_ENDIAN_DESC
689#define uhci_big_endian_desc(u) ((u)->big_endian_desc)
690
691/* cpu to uhci */
692static inline __hc32 cpu_to_hc32(const struct uhci_hcd *uhci, const u32 x)
693{
694 return uhci_big_endian_desc(uhci)
695 ? (__force __hc32)cpu_to_be32(x)
696 : (__force __hc32)cpu_to_le32(x);
697}
698
699/* uhci to cpu */
700static inline u32 hc32_to_cpu(const struct uhci_hcd *uhci, const __hc32 x)
701{
702 return uhci_big_endian_desc(uhci)
703 ? be32_to_cpu((__force __be32)x)
704 : le32_to_cpu((__force __le32)x);
705}
706
707#else
708/* cpu to uhci */
709static inline __hc32 cpu_to_hc32(const struct uhci_hcd *uhci, const u32 x)
710{
711 return cpu_to_le32(x);
712}
713
714/* uhci to cpu */
715static inline u32 hc32_to_cpu(const struct uhci_hcd *uhci, const __hc32 x)
716{
717 return le32_to_cpu(x);
718}
719#endif
720
721#endif
722